How to determine whether you need better attic ventilation
In the summer, good attic ventilation reduces heat buildup. That cuts cooling costs and prolongs shingle life. In the winter, warm, moist air seeps into the attic from the living space below. Good ventilation allows the heat and moisture to escape. That keeps your attic dry and reduces ice dams. Here are four signs of an unventilated or under ventilated attic:
- Look at your eaves and roof. If you don’t see any attic vents on the roof or in the eaves, you need to add some. Your roof vents may not look anything like the ones shown in this article. Your roof may have a ridge vent, which is a low profile, continuous roof air vent running along the peak of the roof. Or it may have gable vents, which are louvered openings at the top of gables.
- Touch your ceiling on a warm, sunny day. A hot ceiling tells you that the attic is acting like a solar oven, raising your cooling bills and cooking the shingles.
- Thick ridges of ice on your eaves in winter are a sign of poor attic ventilation. Warm air that escapes rooms below gets trapped in the attic. Snow melts and the water refreezes on the cold eaves, creating ice dams.
- Warm air that escapes living space also carries moisture that will condense on rafters or roof sheathing. Grab a flashlight and inspect your attic during the winter. If you see dampness or frost, you need better roof ventilation and some attic vents.
For the best results, place roof ventilation near the roof’s peak and soffit vents in the eaves. Air flows in through the soffit vents and out through the roof vents. Vents come in various styles. We chose rectangular, hooded roofing vents and rectangular soffit vents because they’re easy to install. Everything you need to begin a how to roof ventilators project is available at home centers. Aside from vents, you’ll need a handful of 1-1/4 in. roofing nails, 1/2-in. galvanized sheet metal screws for the soffit vents, utility knife blades, a dust mask and one tube of roofing cement for every three vents. You’ll cut holes for the vents with a jigsaw or reciprocating saw. Expect to spend a full day on this project. A cool day is best. On a warm day, attics can get dangerously hot. Heat also makes shingles easy to damage.
How many vents do you need? First determine your attic area by multiplying the length by the width. A 30 x 40-ft. attic, for example, has an area of 1,200 sq. ft. Then aim for about 1 sq. ft. (144 sq. in.) of vent opening per 150 sq. ft. of attic. The building code lets you reduce that by half under some conditions, but more roof ventilation is usually better. The open area of a vent is sometimes listed on the roof air vent as NFVA (net free vent area). If not, measure the size yourself. Roof vents will provide about half of the vent area and soffit vents the other half.
How to install roof vents
Photo 1: Mark attic roof air vent locations
Center nails between rafters 18 in. from the roof’s peak. Drive nails up through the sheathing and shingles to mark roof air vent locations.
Photo 2: Cut the shingles for roof vents
Cut shingles with a utility knife. Make the cutout area 1/2 in. larger than the vent opening. Chalk provides an easy-to-see cutting line.
Photo 3: Cut the hole for roof vents
Cut a hole in the roof sheathing with a jigsaw or reciprocating saw. Drill a starter hole so you can insert the blade to begin the cut.
Photo 4: Remove any obstructions
Slip a pry bar between the shingles and separate the self-sealing adhesive. Then remove any shingle nails that prevent the vent from sliding into place.
Photo 5: Place the vent
Slide the vent into place. Nail the lower edge with roofing nails.
Photo 6: Install the attic vent cover
Apply roof cement where shingles meet the vent. Add a dab of cement to secure the shingles to the attic vent cover base.
Adding attic vents is a simple matter of cutting holes and installing vents. Photos 1 – 6 show how it’s done. But before you cut any holes, plan the locations of the attic vents.
Mark the roof venting locations from the attic, where you can see the rafters and avoid placing roofing vents over them. Place all the roof vents on the same side of the roof. If your roof peak runs parallel to the street, put them on the backside, where they’ll be less prominent. Space attic vents evenly and mark the locations by driving nails up through the shingles (Photo 1). Wear a dust mask while working in the attic and lay planks or plywood across rafters so you don’t step though the drywall ceiling below.
Follow photos 1 – 6 for the simple how-to.
How to install soffit vents
Photo 7: Cut soffit vent holes
Cut holes for soffit vents with a jigsaw. Make the hole dimensions 1 in. smaller than the length and width of the vent.
Photo 8: Install the vents
Screw soffit vents into place with the fins pointing toward the house. Prime and paint vents to match the soffit, but don’t plug the inner screen with paint.
Photo 9: Install baffles
Staple baffles into the spaces between rafters so air flowing in through the vents can flow past the insulation.
Plan to place an equal number of soffit vents on both sides of the house, evenly spaced along the soffits. Look for nails and seams in the soffit that indicate framing locations, and avoid placing vents over the framing. To mark cutting lines on the soffit, make a cardboard template that’s 1 in. smaller than the vent. If your house doesn’t have soffits, one solution is to install roof vents near the lower edge of the roof. For better looking solutions, call a roofing supplier (search “Roofing Materials” online).
If your attic is well insulated, the insulation might be plugging the spaces between rafters just above exterior walls. That means air can’t flow from the soffit vents to the roof vents. The solution is to add baffles, which allow air to flow past the insulation (Photo 9). Baffles are available at home centers. Installing them can be a nasty job, done in a dark, cramped, dusty space. In an older home, you might also find wood blocking between rafters that needs to be cut, pried or drilled out in order to open an air passage.
- Buy roof jacks ($7 each). These metal brackets support a plank that keeps you and your tools from sliding down the roof.
- Rent a personal fall arrest system (PFAS). You may have to call several rental centers to find one.
- Wear soft-soled shoes for the best traction.
- Clean up sawdust and debris to prevent slips and trips.
- Wet shingles are slippery. Stay off them until they dry.
Required Tools for this Roof Vent Installation Project
Have the necessary tools for this DIY attic vents project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Caulk gun
- Drill/driver - cordless
- Dust mask
- Pry bar
- Spade bit - 3/4-in.
- Tape measure
- Utility knife
Required Materials for this Roof Vent Installation Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Attic insulation baffles
- Roof cement
- Roof vents
- Roofing nails
- Sheet metal screws
- Soffit vents